UNS 0121A-Z,V1励磁调节器,UNS 0121A-Z,V1使用进展
最大负载/当前偏移
对于连接到腹板张力电子装置PFEA111/112的每个称重传感器，最大负载范围为±6.5 x Fnom的存储器将存储施加到称重传感器上的最高负载。最大载荷包括：
•称重传感器零信号（称重传感器无负载）
•FRT，称重传感器测量方向上皮重的作用力分量
•FR，测得的力（测量方向上的张力力分量称重传感器）。如果更换称重传感器，可以重置最大负载记忆。
3.12.9.2重置A/B重置A将“MaximumLoad A”设置为零。重置B将“最大负载B”设置为零。
3.12.9.3仿真功能模拟可以设置为打开或关闭。
UNS 0121A-Z,V1励磁调节器如果simulation设置为ON，则参数PercentofNoma和PercentofNomb将为显示。如果在ObjectType和中选择了单面A，则不会显示PercentofNomb如果在ObjectType中选择了单面B，则不会显示PercentofNoma。参数PercentOfFnom可以一步一步地设置在–100和+200之间。什么时候simulation设置为ON，它将替换称重传感器的测量值。值+100表示该值与加载到Fnom的称重传感器相同。
激活模拟时不能使用零集。当模拟设置为ON时，红色状态led点亮，显示屏上显示消息“Simulation”（模拟）。如果按下“ok”（确定），则消息以与故障和警告相同的方式移动到操作员菜单的底部信息。
SetFactory Default将模拟设置为关闭。将“模拟”设置为“开”时，默认值为：–正常百分比=55%
–PercentOfFnomB=45%“服务”菜单具有只能查看的参数和可以设置的参数。
UNS 0121A-Z,V1励磁调节器•只能查看的参数：–软件版本号–最大负载A
显示自上次重置以来的最大负载–当前偏移量A
显示上次零点设置时的零点偏移–最大负载B显示自上次重置以来的最大负载–当前偏移量B
显示上次零点设置时的零点偏移•可设置的参数：–重置A此操作将“最大负载A”设置为零。–重置B此操作将“最大负载B”设置为零。
–模拟激活/停用模拟功能。
Maximum Load / Present Offset
For each load cell connected to the web tension electronics PFEA111/112, a maximum load
memory, with the range ±6.5 x Fnom, will store the highest load that is applied to the load cell.
The maximum load consists of:
• Load cell zero signal (with no load on the load cell)
• F
RT, applied force component of tare in the measuring direction of the load cell
and
• F
R, measured force (force component of tension in the measuring direction of
the load cell).
The maximum load memory can be reset if a load cell is replaced.
3.12.9.2 Reset A/B
Reset A sets “MaximumLoad A” to zero.
Reset B sets “MaximumLoad B” to zero.
3.12.9.3 Simulation function
Simulation can be set to ON or OFF.
If simulation is set to ON, the parameters PercentOfFnomA and PercentOfFnomB will be
displayed. PercentOfFnomB is not shown if Single side A has been selected in ObjectType and
PercentOfFnomA is not shown if Single side B has been selected in ObjectType.
The parameter PercentOfFnom can be set between –100 and +200 in steps of one. When
simulation is set to ON, it replaces the measured value from the load cells. The value +100
means that the value is the same as load cell loaded to Fnom.
Zero set can not be used when simulation is activated. When simulation is set to ON, the red
status led is lit and on the display the message “Simulation” is shown. If “ok” is pressed, the
message is moved to the bottom of the Operator menu in the same way as failure and warning
messages.
SetFactory Default sets the simulation to OFF.
When simulation is set to ON, the default values are:
– PercentOfFnomA = 55%
– PercentOfFnomB = 45%
