ICS TRIPLEX 9451处理器模块
6.要验证消息是否已添加，请查看S1 469 SETUP（设置）×DEFAULT MESSAGES（默认消息）子组中的最后一条消息。使用以下步骤删除默认消息：1。为S1 469 SETUP（设置）passcode（密码）Enter passcode for ACCESS（进入密码）设定点输入正确的密码（除非密码已输入或密码为“0”，否则会破坏密码安全功能）。2.在S1 469 SETUP（设置）×DEFAULT MESSAGES（默认消息）子组下选择要删除的消息。3.当显示要删除的默认信息时，按。继电器显示PRESS[ENTER]TO REMOVE DEFAULT MESSAGE（按下[ENTER]TO删除默认信息）消息。4.按下可从默认消息列表中删除当前消息。5.如果正确遵循该程序，将显示以下闪光消息：n默认消息n[ENTER]了解更多电机状态：停止范围：n/A A:0 B:0范围：n/A电机负载：0.00 x FLA范围：n/B当前不平衡：0%范围：n/C日期：1995年1月1日时间：12:00:00范围：不适用MULTILIN 469电机管理继电器范围MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESTAGE MESSAGE MESSAGE ENTER ENTER ENTER输入4-10 469电机管理继电器GE Multilin 4.2 S1 469 SETUP 4 SETPOINT 4 4.2.6 MESSAGE SCRATCHPAD PATH:SETPOINT？S1 469设置？MESSAGE SCRATCHPAD最多可在消息草稿区域下编程五（5）个消息屏幕。这些信息可能是与安装或电机相关的注释，或用户认为相关的任何其他信息。此外，可以在默认消息显示期间选择这些消息进行扫描。这可能有助于提醒操作员执行某些任务。可以从通信端口或通过键盘输入消息。以下过程演示了消息草稿行的使用：1。选择要更改的用户消息。2.按十进制[.]键进入文本模式。下划线光标将出现在第一个字符下。3.使用/键显示所需字符。空格与字符一样被选中。4.按十进制[.]键前进到下一个字符。要跳过字符，请按十进制键。如果意外存储了不正确的字符，请按十进制键足够多次以将光标滚动到该字符。5.当显示所需信息时，按存储或退出。该消息现在永久存储。按下可取消更改的消息。4.2.7清除数据路径：设置点S1 469设置×清除数据n消息SCRATCHPAD n[ENTER]（输入）更多文本1范围：40个字母数字字符文本2范围：40字母数字字符TEXT3范围：40字符数字字符文本4范围：40位字母数字字符MULTILIN 469电机管理继电器范围：40字节数字字符n清除数据n[ENTEP]（输入]更多清除上次跳闸数据：否范围：否，是重置MWh和Mvarh仪表：否范围：否、是清除峰值需求数据：否范围，是清除RTD最大值：否范围；否，是清除模拟I/P最小值/最大值：无范围：否；是清除跳闸计数器：否范围，是的，输入ESCAPE（退出）信息
6. To verify that the message was added, view the last message in the S1 469 SETUP Õ× DEFAULT MESSAGES subgroup. Use the following procedure to remove default messages: 1. Enter the correct passcode for the S1 469 SETUP Õ PASSCODE Õ ENTER PASSCODE FOR ACCESS setpoint (unless the passcode has already been entered or unless the passcode is “0”, defeating the passcode security feature). 2. Select the message to remove under the S1 469 SETUP Õ× DEFAULT MESSAGES subgroup. 3. When the default message to be removed is shown, press . The relay displays the PRESS [ENTER] TO REMOVE DEFAULT MESSAGE message. 4. Press to remove the current message from the default message list. 5. If the procedure was followed correctly, the following flash message will be displayed: n DEFAULT MESSAGES n [ENTER] for more MOTOR STATUS: Stopped Range: N/A A: 0 B: 0 Range: N/A MOTOR LOAD: 0.00 x FLA Range: N/A CURRENT UNBALANCE: 0% Range: N/A DATE: 01/01/1995 TIME: 12:00:00 Range: N/A MULTILIN 469 Motor Management Relay Range: N/A DEFAULT MESSAGE HAS BEEN ADDED DEFAULT MESSAGE HAS BEEN REMOVED ENTER ESCAPE ð ð MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE MESSAGE ENTER ENTER ENTER ENTER 4-10 469 Motor Management Relay GE Multilin 4.2 S1 469 SETUP 4 SETPOINTS 4 4.2.6 MESSAGE SCRATCHPAD PATH: SETPOINTS Õ S1 469 SETUP Õ× MESSAGE SCRACTHPAD Up to five (5) message screens can be programmed under the Message Scratchpad area. These messages may be notes that pertain to the installation or the motor or any other information deemed pertinent by the user. In addition, these messages may be selected for scanning during default message display. This might be useful for reminding operators to perform certain tasks. The messages may be entered from the communications ports or through the keypad. The following procedure demonstrates the use of the message scratchpad: 1. Select the user message to be changed. 2. Press the decimal [.] key to enter text mode. An underline cursor will appear under the first character. 3. Use the / keys to display the desired character. A space is selected like a character. 4. Press the decimal [.] key to advance to the next character. To skip over a character press the decimal key. If an incorrect character is accidentally stored, press the decimal key enough times to scroll the cursor around to the character. 5. When the desired message is displayed press to store or to quit. The message is now permanently stored. Press to cancel the altered message. 4.2.7 CLEAR DATA PATH: SETPOINTS Õ S1 469 SETUP Õ× CLEAR DATA n MESSAGE SCRATCHPAD n [ENTER] for more TEXT 1 Range: 40 alphanumeric characters TEXT 2 Range: 40 alphanumeric characters TEXT 3 Range: 40 alphanumeric characters TEXT 4 Range: 40 alphanumeric characters MULTILIN 469 MOTOR MANAGEMENT RELAY Range: 40 alphanumeric characters n CLEAR DATA n [ENTER] for more CLEAR LAST TRIP DATA: No Range: No, Yes RESET MWh and Mvarh METERS: No Range: No, Yes CLEAR PEAK DEMAND DATA: No Range: No, Yes CLEAR RTD MAXIMUMS: No Range: No, Yes CLEAR ANALOG I/P MIN/MAX: No Range: No, Yes CLEAR TRIP COUNTERS: No Range: No, Yes PRESET DIGITAL COUNTER: No Range: No, Yes CLEAR EVENT RECORDER: No Range: No, Yes ENTER ESCAPE ð ð MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE VALUE VALUE ENTER ESCAPE ESCAPE ENTER ESCAPE ð ð MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE
