MIV08A-1-B5工控模块系统备件
与这些区域的间隙应大于或等于电缆直径。3.保持电缆弯曲在第7页规范中列出的弯曲半径内。以下列出了电缆弯曲半径的一般准则，但是，单个电缆可能有其他限制：网络电缆的静态或一次性弯曲半径为电缆直径的十二倍。4.安装这些电缆时应遵守这些限制：防止电缆在150±25（6±1 in.）安装区域内弯曲。仅在弯曲区域将电缆弯曲为特定形状。沿电缆线路以3米（10英尺）的间隔提供电缆支架，以减少连接器和电缆上其他部件的张力和弯曲。5.施加0.81.2 Nm（711 lbin）的扭矩，使控制装置完全就位并固定连接。注意：如果在IDM系统通电时连接或断开电缆，可能会发生电弧或意外运动。在IDM系统上工作之前，断开电源并等待IPIM模块警告中所示的整个时间间隔，或者验证IPIM模块上的总线电压是否小于50V。如果不遵守此预防措施，可能会导致严重的人身伤害或生命损失，并对产品造成损坏。有限弯曲区安装区域150±25（6±1.0）安装区域150？5（6±1.02090-CNSSPRS-AA所示M12直角内螺纹插头M12直外螺纹插头尺寸为英寸和英寸。). 6 Kinetix 6000M A系列网线出版物2090-IN034B-EN-P-2012年3月原理图和连接器引脚图该图提供了Kinetix 6000 M网线的导线颜色和引脚。网络电缆示意图网络电缆引出线网络电缆配置不用于连接到IPIM模块。1 4 2 3 5 1 4 2 5蓝白/蓝白/棕棕色屏蔽双绞线屏蔽线连接1。屏蔽连接到两个连接器的螺纹金属端。绿色公连接器引脚母连接器引脚2090 CNSSPRS AAxx直阳和直角阴2090 CNSRPSS AAxx直角阳和直阴2090 CNSSPSS AAxx直阴和直阳2090 CNRSPRS AAxx直角阴和直角阳Kinetix 6000M系列A网络电缆7出版物2090-IN034B-EN-P-2012年3月附加规范在Kinetix Motion处理器技术数据出版物GMC-TD004中提供了eh电缆的规格。附加资源这些文件包含罗克韦尔自动化公司相关产品的附加信息。您可以在以下位置查看或下载出版物：http://../literature.要订购技术文件的纸质副本，请联系您的Allen-Bradley®分销商或罗克韦尔自动化®销售代表。
Clearance from these areas should be greater than or equal to the cable diameter. 3. Keep cable bends within the bend radius listed in the Specifications on page 7. General guidelines for the bend radius of a cable are listed below, however, individual cables may have additional restrictions: Network cables have a static or one-time bend radius of twelve times the cable diameter. 4. Observe these restrictions when installing these cables: Prevent the cable from flexing within 150 ±25 (6 ±1 in.) installation areas. Bend cables to a specific shape only in the bend zone area. Provide cable supports at 3 m (10 ft) intervals along the cable run to uce tension and flexing at the connectors and other features on the cable. 5. Apply 0.81.2 Nm (711 lbin) of torque to fully seat the contts and secure the connection. ATTENTION: Arcing or unexpected motion can occur if cables are connected or disconnected while power is applied to the IDM system. Before working on an IDM system, disconnect power and wait the full time interval as indicated in the warning on the IPIM module or verify the bus voltage at the IPIM module measures less than 50V . Failure to observe this precaution could result in severe bodily injury or loss of life, and damage to the product will occur. Limited Bend Zone Installation Area 150 ± 25 (6 ± 1.0) Installation Area 150 ± 25 (6 ± 1.0) 2090-CNSSPRS-AA shown M12 Right-angle Female Plug M12 Straight Male Plug Dimensions are in and (in.). 6 Kinetix 6000M Series A Network Cable Publication 2090-IN034B-EN-P - March 2012 Schematic and Connector Pinouts The diagrams provides wire colors and pinouts for the Kinetix 6000M network cables. Network Cable Schematic Network Cable Pinouts Network Cable Configurations Not for connection to an IPIM module. 1 4 2 3 5 1 4 2 3 5 Blue White/Blue White/Brown Brown Shield Twisted Pair Shield Wire Connection 1. Shield connects to the threaded metal end of both connectors. Green Male Connector Pinouts Female Connector Pinouts 2090-CNSSPRS-AAxx Straight Male and Right-angle Female 2090-CNSRPSS-AAxx Right-angle Male and Straight Female 2090-CNSSPSS-AAxx Straight Male and Straight Female 2090-CNRSPRS-AAxx Right-angle Male and Right-angle Female Kinetix 6000M Series A Network Cable 7 Publication 2090-IN034B-EN-P - March 2012 Specifications Additional specifications for eh cable are available in the Kinetix Motion cessories Technical Data, publication GMC-TD004. Additional Resources These documents contain additional information concerning related products from Rockwell Automation. You can view or download publications at http://../literature. To order paper copies of technical documentation, contt your Allen-Bradley® distributor or Rockwell Automation® sales representative.
