MOTOROLA MVME 147-023工控模块卡件
固态设备用途广泛，所有负责使用该设备的人员必须确保该设备的预期应用是可接受的。在任何情况下，罗克韦尔自动化公司均不对因使用或应用本设备而导致的间接或间接损害负责。本手册中的示例和图表仅用于说明目的。由于与任何特定安装相关的许多变量和要求，罗克韦尔自动化公司不能根据示例和图表承担实际使用的责任。Rockwell Automation，Inc.对本手册中描述的信息、电路、设备或软件的使用不承担任何专利责任。未经股份有限公司书面许可，禁止复制本手册的全部或部分内容。在本手册中，如有必要，我们使用注释使您了解安全注意事项。警告：识别在危险环境中可能导致爆炸的事件或情况的信息，这可能导致人身伤害或死亡、财产损失或经济损失。注意：识别可能导致人身伤害或死亡、财产损失或经济损失的事件或情况的信息。注意事项有助于识别危险、避免危险并认识到后果。电击危险：标签可能位于设备上或设备内部，例如驱动器或电机，以提醒人们可能存在危险电压。烧伤危险：标签可能在设备上或设备内部，例如，驱动器或电机，以提醒人们冲浪可能会恢复危险的温度。重要信息确定对成功应用和理解产品至关重要的信息。Kinetix 6000M系列A网络电缆3出版物2090-IN034B-EN-P-2012年3月开始移除物品内部和周围的所有包装材料。拆开后，根据采购订单验证目录号，并目视检查电缆和eh连接器是否损坏。如有必要，及时通知承运人任何运输损坏。电缆以线圈形式存放和运输，除非您拉直电缆，否则电缆将保持这种形状。要拉直电缆，请从电缆的中点悬挂一根短电缆，或将一根长电缆笔直地放在地板上。任何持续的盘绕应在24小时内放松。这样做会使电缆更易于安装。在伺服系统中安装电缆时，请遵守以下注意事项。不遵守这些安全注意事项可能导致人身伤害或电机和设备损坏。电击危险：为避免电击危险，请确保在至少一个点处接地所有供电电缆。the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that eh intended application of this equipment is ceptable. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for tual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING: Identifies information about prtices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about prtices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize the consequences. SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that surfes may reh dangerous temperatures. IMPORTANT Identifies information that is critical for successful application and understanding of the product. Kinetix 6000M Series A Network Cable 3 Publication 2090-IN034B-EN-P - March 2012 Before You Begin Remove all pking material from within and around the item. After unpking, verify the catalog number against the purchase order, and visually inspect the cable and eh connector for damage. If necessary, iediately notify the carrier of any shipping damage. Cables are sto and shipped in a coil, and will retain this shape unless you straighten the cable. To straighten a cable, hang a short cable from its mid-point or lay a long cable on the floor in a straight line. Any coiling that persists should relax within 24 hours. Doing this results in a cable that is easier to install. Observe the following precautions when installing the cables in a servo system. Failure to observe these safety notices could result in personal injury or damage to the motor and equipment. SHOCK HAZARD: To avoid the hazard of electrical shock, be sure to ground any cable providing power at a minimum of one point.
