产品详情内容介绍
Kollmorgen 6SM77K-3.000-G-J-09-HA-IN伺服电动机
静电放电意识使用或靠近控制装置时，请遵循这些预防措施。
1.不穿衣服，避免身体上积聚静电由合成材料制成。
尽量穿棉质或棉混纺材料尽可能的，因为它们不储存那么多的静电合成材料。
2.不要从控制柜上拆下印刷电路板（PCB）除非绝对必要。如果必须从控件中卸下PCB机柜，请遵循以下预防措施： 请勿触摸PCB的任何部分，边缘除外。
不要触摸电导体、连接器或用导电设备或用手操作的部件。
更换PCB时，请将新PCB保持在塑料防静电中在您准备好安装之前，它会一直放在保护袋中。
立即从控制柜中卸下旧PCB后，将其放在防静电保护袋。
安全使用的特殊条件需要安装固定接线。
现场接线必须符合北美I级2区（CEC和NEC）或欧洲2区，适用的3类接线方法，并符合当地具有管辖权的检验机构。
现场接线必须适合在高于环境温度至少10°C的条件下进行活动
505数字控制需要使用PE端子接地
A开关或断路器应包括在关闭的建筑安装中靠近设备且操作员易于接近。
开关或断路器应清楚标记为设备开关或断路器不得中断保护接地（PE）导线。
505数字控制适用于欧洲2区IIC组安装在IP54最低额定外壳中时的环境60079-0和EN 60079-15。
该设备必须安装在一个足够的区域或外壳内防止大于2焦耳的冲击和灰尘或水进入。
对于ATEX/IECEx，505数字控制应安装在一个外壳内，该外壳编码Ex nA，最低防护等级为IP54。
安装人员应确保最高周围空气温度不超过额定值最终安装位置的温度为+70°C。
505数字控制不得安装在IEC规定的污染等级超过2级的区域60664-1.正常操作时，不得接近外壳内部不使用工具。
本手册介绍了汽轮机的伍德沃德505数字调速器带单量程或分量程执行器。
发布版本为8200-1300，8200-1301和8200-1302。
下面的选项图表显示了差异零件号之间。
本手册第1卷提供了安装说明，描述控件，并解释配置（编程）和操作程序。
第2卷包括关于将控件应用于特定应用程序、服务模式信息和505硬件规格。
本手册不包含完整的操作说明汽轮机系统。
Electrostatic Discharge Awareness
Follow these precautions when working with or near the control. 1. Avoid the build-up of static electricity on your body by not wearing clothing made of synthetic materials. Wear cotton or cotton-blend materials as much as possible because these do not store static electric charges as much as synthetics. 2. Do not remove the printed circuit board (PCB) from the control cabinet unless absolutely necessary. If you must remove the PCB from the control cabinet, follow these precautions: Do not touch any part of the PCB except the edges. Do not touch the electrical conductors, the connectors, or the components with conductive devices or with your hands. When replacing a PCB, keep the new PCB in the plastic antistatic protective bag it comes in until you are ready to install it. Immediately after removing the old PCB from the control cabinet, place it in the antistatic protective bag.
The 505 Digital Control is suitable for use in European Zone 2, Group IIC environments when installed in an IP54 minimum rated enclosure per s EN 60079-0 and EN 60079-15. This equipment must be installed in an area or enclosure providing adequate protection against impact greater than 2 Joules and the entry of dust or water. For ATEX/IECEx the 505 Digital Control shall be installed in an enclosure that is coded Ex nA, providing a minimum IP54 ingress protection. The installer shall ensure that the maximum surrounding air temperature does not exceed the rated temperature of +70 °C at the final installation location. The 505 Digital Control shall not be installed in areas exceeding Pollution Degree 2 as defined in IEC 60664-1. The interior of the enclosure shall not be accessible in normal operation without the use of a tool.
Special Conditions for Safe Use
A fixed wiring installation is required. Field wiring must be in accordance with North American Class I, Division 2 (CEC and NEC), or European Zone 2, Category 3 wiring methods as applicable, and in accordance with the Local Inspection Authority having jurisdiction. Field wiring must be suitable for at least 10 °C above ambient conditions during operation. Grounding of the 505 Digital Control is required using the PE terminal. A switch or circuit breaker shall be included in the building installation that is in close proximity to the equipment and within easy reach of the operator. The switch or circuit breaker shall be clearly marked as the disconnecting device for the equipment. The switch or circuit breaker shall not interrupt the Protective Earth (PE) conductor.
This manual describes the Woodward 505 Digital Governor for steam turbines with single or split-range actuators. Released versions are 8200-1300, 8200-1301, and 8200-1302. The option charts below show the differences between the part numbers. Volume 1 of this manual provides installation instructions, describes the control, and explains the configuration (programming) and operating procedures. Volume 2 includes notes on applying the control to specific applications, Service mode information, and 505 hardware specifications. This manual does not contain instructions for the operation of the complete turbine system. For turbine or plant operating instructions, contact the plantequipment manufacturer.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营产品文字介绍
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
